News

Fiberglass light poles advantages: 1. Light weight, high strength: FRP material strength and advanced alloy steel equivalent to a density of 1.5 to 2.0, carbon steel 1/4 to 1/5, the tensile strength considerably. Therefore, the same size pole, the weight fiberglass poles are steel bar about 1/3, based on this characteristic, fiberglass lamp poles, which are particularly suitable for bridge load requirements of local authorities.  2. Resistance to corrosion resistance: FRP is a good corrosion-resistant materials, there is resistance to air, water and general concentration of acid, alkali, salt, and a variety of oils and solvents good. Fiberglass poles therefore well adapted to humid and rainy south and the air in the higher salinity of coastal cities. In the poles throughout the service cycle, appearance and internal will not be any significant change. This is unmatched by ordinary steel bars.  3. Good insulation: FRP is a good insulating material used to make insulators. So fiberglass light poles will not shock injury accident caused by leakage occurs during use. Although the metal pole grounding protection device installed, but ultimately can not avoid fool proof. So fiberglass poles higher (such as sidewalks, parks) and other local safety requirements, it has certain advantages. 4. Maintenance-free: fiberglass poles because of corrosion over the entire life cycle does not require maintenance, which uses a special surface coating materials, can guarantee ten years there will be no significant fading. At relatively scarce street maintenance funding situation, more highlight our advantage. 5. The surface is smooth and beautiful: fiberglass pole and the outer surface of the coating material has a good affinity, sostreetlight surface is very smooth after molding, and more beautiful than ordinary steel rod.  6. Low installation costs: fiberglass light poles because of its light weight, so no crane installation, the installation is simple and quick little impact on traffic. In the streetlight project, labor costs account for about 20% to 30% of the total cost, if you use fiberglass poles can effectively reduce costs in this area. 7. The strong wind resistance: FRP materials have a slight elasticity, fiberglass poles in the typhoon comes, will have an amplitude of about 10%, but it is plastically deformed after the typhoon, it will spring back to the original position. Bamboo wind with its principle is similar.

Read More

Roll wrapped carbon fiber round tubes are widely used in various industries due to their high strength-to-weight ratio and exceptional properties. Carbon fiber is a lightweight and durable material that is highly resistant to corrosion, fatigue, and impact. The manufacturing process involves wrapping carbon fiber layers over a mandrel, which is then cured under high heat and pressure. This process creates a seamless tube that is both strong and lightweight.One of the significant advantages of roll wrapped carbon fiber round tubes is their stiffness. They have a high modulus of elasticity, meaning they can resist bending and flexing without undergoing significant deformation. The stiffness of carbon fiber also results in improved performance and stability, making it an excellent material for aerospace and sporting goods industries.Another benefit of carbon fiber tubes is their strength. Carbon fiber is known for its high tensile strength, making it an ideal material for components that require high strength and durability. Carbon fiber tubes can withstand high loads and pressures without deforming or breaking, providing long-term reliability and performance.Corrosion resistance is another advantage of carbon fiber tubes. Unlike traditional materials, such as steel or aluminum, carbon fiber does not corrode or rust. This characteristic is especially beneficial in marine and water applications where corrosion can lead to failure and downtime.Dimensional stability is another key feature of roll wrapped carbon fiber round tubes. Unlike other composite manufacturing processes, roll wrapping results in a uniform wall thickness through the entire length of the tube. This uniformity ensures consistent mechanical properties and dimensional accuracy, making roll wrapped carbon fiber tubes ideal for precision applications.Roll wrapped carbon fiber round tubes can be customized to specific lengths, diameters, and thicknesses to meet customers' unique application requirements. They can also be manufactured in various shapes, such as square, rectangular, and oval. This versatility makes carbon fiber tubes an attractive option for a wide range of applications.Carbon fiber tubes have found applications in many industries, including aerospace, automotive, marine, and sporting goods, among others. In the aerospace industry, carbon fiber tubes are used in aircraft components, such as wing spars and fuselage structures. In the automotive industry, carbon fiber tubes are used in lightweight racing cars and high-performance vehicles. In the marine industry, carbon fiber tubes are used in boat and shipbuilding, enabling them to withstand heavy loads and harsh marine environments. In the sporting goods industry, carbon fiber tubes are used in fishing rods, kites, and bicycles due to their lightweight and stiffness.In conclusion, roll wrapped carbon fiber round tubes are an excellent choice for structural applications that require high strength, stiffness, and corrosion resistance. With their exceptional properties, they are widely used in many industries, making them a versatile and cost-effective solution for various applications. The continuous development of carbon fiber manufacturing technology and the increasing demand for lightweight and durable materials ensure that carbon fiber composites will continue to be an important material for the future.

Read More

For serious offshore fisherman, outriggers are considered essential equipment. The purpose of outriggers are to widen a spread and create ability to add more lines in the water without fear of entanglement. In this article we will compare the benefits and uses of different types of outriggers on offshore fishing boats.  Fixed Length OutriggersFixed length outriggers are the most basic and traditional type of outriggers that are still popular among offshore anglers. Fixed outriggers are typically made of sturdy materials such as aluminum or fiberglass and are designed to handle heavy loads. They are also relatively affordable easy to install and typically can only swing outward. The main benefit of fixed outriggers is their durability and reliability. They are built to last and can withstand the harsh offshore environment. They are also very stable and provide a solid platform for multiple fishing lines. Fixed outriggers are ideal for anglers who prefer a simple and straightforward fishing setup.  Telescoping OutriggersTelescoping outriggers are designed to be adjustable in length, which allows anglers to extend their fishing reach and be able to lower the height of the overall vessel. They are made up of several sections that can be extended or retracted as needed. Telescoping outriggers are typically made of lightweight materials such as aluminum or carbon fiber and are easy to maneuver. The main benefit of telescoping outriggers is their versatility. They can be adjusted to different lengths depending on the fishing conditions, and they can be collapsed for easy storage when not in use. Telescoping outriggers are ideal for anglers who want a flexible and adaptable fishing setup. Mounting Styles: Gunwale Or HardtopConventional outriggers are designed with a side-mounted style, where they are attached to the gunwales of the boat. This feature allows for efficient trolling and is popular among mid-size fishing boats. Gunwale-mounted outriggers are less costly than the hardtop-mounted, but they can be obstructive depending on the boat and only come in certain sizes.  Hardtop-mounted outriggers are mounted at a higher point on the boat which provides more space for those on board.  This comes at a price, as hardtop-mounted outriggers are usually more expensive and you may have to climb on top of the hardtop to put them out which can be risky, especially if it is a rough day offshore.  Carbon Fiber OutriggersCarbon fiber outriggers are the newest and most advanced type of outriggers available on the market. Lightweight and incredibly strong, carbon fiber allows for a thinner and more flexible option which is designed to reduce drag and improve fuel efficiency. Easy to maneuver and quickly adjusted to different lengths and positions as needed, carbon fiber outriggers are ideal for anglers who want the most advanced and high-performance outriggers available. In conclusion, outriggers are essential equipment for offshore fishing boats, and choosing the right type of outrigger depends on your personal fishing style and preferences.     No matter which type of outrigger you choose, it will undoubtedly help you to extend your fishing reach, get more lines in the water, and improve your chances of catching more fish!

Read More

43 employees from our company recently embarked on a 5-day adventure to Inner Mongolia, from the 26th to the 30th of the month. As part of our company's ongoing efforts to promote a strong sense of camaraderie and cooperation among our staff, we regularly hold team-building activities.During our trip, we participated in various group activities, including horseback riding, archery, and snow sliding. It was a wonderful opportunity for us to bond and strengthen our teamwork skills.Our company strongly believes in the benefits of taking breaks and engaging in leisure activities to recharge and promote mental well-being. Therefore, we encourage our employees to work hard when it's needed, but also to let loose and have a bit of fun.Overall, our trip to Inner Mongolia was a great success and an unforgettable experience that we will always cherish. We look forward to planning many more such outings in the future.    

Read More

Why Is Gutter Maintenance Important? A gutter with a gutter bracket full of wet leaves and pollen. Leaves and twigs can build up over time and clog your home’s gutters and downspouts. You may also notice sections of the gutters are leaking, are sagging or have separated from the house. Gutters that aren’t working correctly can allow water to damage your roof, foundation and more. If water doesn’t flow through the gutter system, it can collect under the roofing and damage shingles, underlayment and decking. Water under the roofing can also leak into your home, damaging ceilings, walls and floors, and allowing mold growth. In winter, water trapped in gutters can freeze, forcing ice back under the edge of the shingles and resulting in leaks when the warm air under the roof melts the ice. In addition, the weight of debris and accumulated water in a clogged gutter may cause it to pull away from the roof, creating gaps. Water can then cause damage and rot under the fascia that runs along the edge of the roof. If clogged or damaged gutters allow water to reach your home’s foundation, the water can soften the ground, leading to cracks in the foundation. A damaged foundation can create more problems inside, including damaged floors, warped door and window frames, and cracks in walls. The water can also reach your crawlspace or basement, leading to more moisture and mold problems. While poorly maintained gutters can cause expensive problems, you can avoid damage to your home, and the cost to repair it, if you follow a couple of simple steps. 1.Clean your gutters at least twice a year — once in the spring and then once again in the fall. 2. Check the gutters before and after heavy rain showers to make sure they’re still clear. How to clean your gutters? 1.With an Extension Pole As long as your gutters are not thoroughly clogged, you can clean them successfully with a garden hose. For the best results, it’s important that the hose be equipped with the proper attachment (a rigid tube with a curved end). By using an extension, such as the GutterMaster Telescopic Water Fed Pole, you can stand on the ground, not on a ladder, as you work. Start at the end nearest the downspout, spray out the entire channel length, and then work your way back to the downspout. Expect some mess—water, leaves, and small twigs are likely to spray over the sides of the gutter, so dress appropriately. 2.With a Ladder Climbing on a ladder to clean the gutters isn’t as safe as cleaning them from the ground because there’s always a risk of falling. To reduce the risk, it’s essential to use the right ladder. Avoid using a step ladder, which can tip. Instead, use a sturdy telescoping ladder that has been fitted with stabilizer arms. These arms can be purchased separately and attached to standard extension ladders. One such example is the Louisville Ladder Stabilizer, which braces the ladder against the siding and keeps it from slipping to the side. In addition, it’s a good idea to have an assistant on the ground who can hold the ladder to stabilize it, and hand you tools as you need them. 3.By Hand To clean gutters by hand, you’ll need a ladder, bucket, gutter scoop (or garden trowel), and heavy-duty work gloves. Little by little, take out the leaves and debris, placing what you remove into the bucket. Finally, flush the gutters and downspout with water until you are certain both are functioning correctly. 

Read More

In recent years, more and more professional window cleaning workers replace their aluminum pole into carbon fiber pole. What's the reason of this situation? As a traditional water fed pole material, aluminum is a great kind of material. It's low cost and much lighter than other metal. It will undoubtedly be superior when compared to other metallic materials. It's just a shame that it's carbon fibre that's up against it in the ring. Carbon Fiber Water Fed Pole 1. Light WeightCarbon fiber only has a density that is nearly half of that of aluminum. Yes, only a half ,the difference between the different models may be even greater. When you're holding up a 30ft pole to clean your windows, would you rather the pole was 1.5kg or 3kg? The answer is obvious. To make the cleaning job less difficult and to speed up the cleaning process, carbon fibre is undoubtedly a perfect choice！ 2. Sturdy and durable: Carbon fiber is extremely strong and durable, making water fed poles made from this material long-lasting and resistant to damage. Carbon fiber poles are less likely to break or crack compared to aluminum or fiberglass poles.3. Non-conductive: Carbon fiber is an insulating material, making carbon fiber water fed poles non-conductive, even when wet. This makes them safer to use when cleaning buildings near electrical wires.4. High reach: Carbon fiber water fed poles are available in lengths that extend up to 80 feet, allowing cleaners to reach upper levels of a building without the need for scaffolding or ladders.5. Chemical resistant: Carbon fiber water fed poles do not corrode when exposed to harsh cleaning chemicals, which makes them ideal for use in industrial cleaning.6. Minimal maintenance: Carbon fiber water fed poles require minimal maintenance, and are easy to clean and store.Overall, carbon fiber water fed poles offer a combination of strength, durability, and lightweight design features that make them a perfect choice for water fed pole cleaning.

Read More

China is celebrating the Dragon Boat Festival, also known as the Duanwu Festival, a traditional holiday that falls on the fifth day of the fifth lunar month.The festival has a history of over 2,000 years, and it commemorates the ancient patriot and poet Qu Yuan. He lived during the Warring States period in ancient China and drowned himself in the Miluo River to protest against corrupt leaders and offer himself as a sacrifice to the river spirits. The festival's main activity is the dragon boat race, where teams of rowers paddle in sync to reach the finish line. The races symbolize the search for Qu Yuan's body and the rescue attempt by the villagers who rode the boats.Apart from the dragon boat race, the festival is also a time for families to come together and enjoy traditional food, such as zongzi, a sticky rice dumpling wrapped in bamboo or reed leaves with various fillings, including pork, egg yolk, and red beans.In addition, many people hang herbs, such as artemisia and calamus, on their doors to ward off evil spirits and diseases.Despite the ongoing COVID-19 pandemic, people across China have been celebrating the Dragon Boat Festival following the necessary precautions and guidelines to ensure everyone's safety.

Read More

During the pandemic, the focus on touchpoint disinfection led to a neglect of other aspects of building cleaning. As more people return to offices, aesthetic aspects such as window cleaning have become important again. To help cleaning professionals stay up to date with trends in window cleaning, Interclean has outlined four notable trends.The first trend is the adoption of pure water cleaning, which involves filtering tap water to remove impurities and using it to clean windows directly with a water-fed brush. This saves time and money while also being more sustainable.The second trend is the use of cobotics, or machine technology, to assist with window cleaning. Cobotic exoskeletons can provide greater range of motion and lessen ergonomic strain for cleaners.Drones are another trend in window cleaning, as they can potentially clean windows without human supervision. However, further advancements are needed to improve their cleaning solution and water capacities, as well as battery lifespan.Finally, ultrasonic cleaning is a technology that can remove dirt from crevices without the need for additional cleaning solutions.Overall, staying current with trends in window cleaning can help cleaning crews optimize their practices and maintain a fresh, aesthetic appearance in buildings.

Read More

The 2024 China Carbon Materials Exhibition is a professional exhibition on the theme of new materials industry under the "24th Industry Expo". Through marketization, specialization, internationalization and branding operations, it has developed into a comprehensive solution for the carbon material industry certified by the International Exhibition Union (UFI). It is also an international event for professional manufacturers and carbon material industry applications. Years of success have established it as one of the most attractive professional exhibitions in the field of carbon materials in China and even Asia, providing an ideal business platform for peers in the industry to meet, gather and interact.   As the largest and globally important carbon materials exhibition in Asia, the China International Carbon Materials Exhibition (and Asia Carbon Materials Exhibition) has always played an important role in promoting the development of the carbon materials industry. The 2024 Asia Carbon Materials Exhibition will be held in September Held at the National Convention and Exhibition Center (Shanghai) from the 24th to the 28th, it will bring together the world's superior carbon material resources, promote precise docking and coordinated development of the industrial chain, and set up the most intuitive and effective communication and docking platform for the carbon materials industry to further improve the application and development of carbon materials promotes cooperation and exchanges between industries, enterprises and the market. Domestic and foreign enterprises, research institutions, associations/society in the application field are sincerely invited to visit, communicate, negotiate and purchase at the exhibition site.  

Read More

Composite carbon fiber material is a new type of high-strength, high-modulus fiber material with a carbon content of more than 90%. It has the characteristics of light weight, high strength, corrosion resistance, high modulus, low density, no creep, and good electrical and thermal conductivity. It not only has the inherent characteristics of carbon materials, but also has the soft processability of textile fibers. It is a new generation of reinforced materials and is known as the "black gold" of the 21st world. This year's government work report proposed that innovation should remain at the core of my country's modernization drive and that scientific and technological self-reliance should be the strategic support for national development. Carbon fiber material is a typical representative of strategic materials and is known as the "King of New Materials" in the field of modern science and technology. Carbon fiber materials support and guarantee the R&D and manufacturing of important national equipment with their outstanding mechanical properties and excellent comprehensive performance.   Since the advent of carbon fiber in the 20th century, foreign carbon fiber technology has been strictly blocked in China, and the development of domestic carbon fiber industry technology has been difficult. After 2000, our country attached great importance to high-performance carbon fiber technology and provided strong top-down support, promoting the development of the domestic carbon fiber industry. Firstly, in terms of production capacity, the total domestic carbon fiber production capacity in 2020 is approximately 30,000 tons, and the total consumption is 38,000 tons; secondly, in terms of products, in the past 20 years, it has achieved full coverage of global conventional product specifications from “nothing”; thirdly in terms of industrial structure, carbon fiber industry clusters have taken shape in the Beijing-Tianjin-Hebei, Yangtze River Delta, Pearl River Delta, and Bohai Rim regions, with a number of iconic companies and R&D institutions emerging. Generally speaking, the rapid development of the domestic carbon fiber industry has benefited from the long-term and orderly support of the state and the entry of social capital.   2021 is the first year of the 14th Five-Year Plan. In the "Action Plan to Accelerate the Development of Carbon Fiber Industry" issued by the Ministry of Industry and Information Technology in October 2013, it was stated that the main problems currently existing in my country's carbon fiber industry are: compared with the international advanced level, my country's carbon fiber industry has weak technological innovation capabilities, imperfect process equipment.There are many problems such as unstable product performance, high production costs, low-level duplication of construction, low level of industrialization of high-end varieties, lagging standardization construction, and serious shortage of downstream application development. On the one hand, because Japanese and American companies strictly restrict the export of high-performance carbon fibers they produce to China, the export of general and complete sets of carbon fiber technologies must be specially approved by the government of the exporting country. Therefore, my country's high-performance carbon fibers have long been dependent on imports, and the supply and demand gap in the carbon fiber industry has reached 70%. On the other hand, our country's blind expansion of low-end carbon fiber products has led to overcapacity and insufficient research and development capabilities for high-end products, which has hindered the profitability of our country's carbon fiber companies. Breaking through high-end technology is an important way to narrow the international gap and is also the key to the development of our country's carbon fiber industry.   "CIME 2023 Shanghai International Composite Materials and Carbon Fiber Materials Exhibition" is a theme exhibition under the 2023 Shanghai International New Materials Thermal Conductivity and Heat Dissipation Materials Exhibition. It will focus on displaying the latest products in new materials, new technologies, and new process industries to establish a brand image for enterprises. Promote trade cooperation and market development, lead the industry trend, strengthen the interaction of production, research and development, and sales, gain in-depth insights into the new trends in the future development of domestic and foreign new material markets, explore new needs of the future new material market with a development perspective, innovate the connotation of the exhibition, and comprehensively , multi-level organization of professional visitors, providing exhibitors and participating merchants with the best platform for technical exchanges, product display and trade negotiations. The 2023 Shanghai International Composite Materials and Carbon Fiber Materials Exhibition will be held at the Shanghai New International Expo Center from December 13th to 15th, 2023. At that time, we warmly welcome domestic and foreign new composite materials, new technologies, new process enterprises and related supporting industries to visit and communicate!   Target audience: We focus on inviting national, provincial, municipal, and related scientific research units, national defense, aviation, aerospace, chemical industry, electronics, consumer electronics, automobile industry, new energy industry, bicycles, motorcycles, sporting goods, semiconductors, military supplies, Shipbuilding, household appliances, wind power, fishing rods and fishing gear, machinery industry, electronic equipment, leisure products, communications/communication networks, medical instruments, wind power, industrial robots, machinery manufacturing, industrial transmission, plastics and rubber, composite materials, marine engineering, defense Executives from corrosion, power electronics and other companies attended the meeting to visit and negotiate.   Range of exhibition:   ◆Composite materials: high-performance fiber materials, polymer matrix materials, metal matrix composite materials, ceramic matrix composite materials, bio-based synthetic materials, glass fiber, polyethylene fiber, polyaramid fiber, carbon fiber short fiber, etc.;   ◆Carbon fiber materials: carbon fiber materials, carbon fiber composite materials, carbon fiber short fibers, other carbon fiber material products, etc.;   ◆Carbon fiber products: leisure and sporting goods, military and aerospace products, automobiles, bicycles, yachts and racing boats, etc.;   ◆Raw materials and production equipment: various resins (unsaturated/epoxy/ethylene/phenolic, etc.), various fibers and reinforcing materials (glass fiber/carbon fiber/basalt fiber/aramid/natural fiber, etc.), adhesives, Various additives, fillers, colorants, premixes, prepregs, as well as production, processing and treatment equipment for the above raw materials; ◆Composite material production technology and equipment: spraying, winding, molding, injection, pultrusion, RTM, LFT, vacuum introduction, autoclave, etc.; honeycomb, foaming, sandwich technology and process equipment, molding mold design and processing technology, etc.;   ◆Composite material quality control and testing: quality monitoring technology and material testing equipment, automation control technology and robots and other equipment, non-destructive testing technology and equipment;   ◆Technology and equipment for energy saving, environmental protection recycling, recycling and repair of composite materials and their products;   ◆Frontier new materials: electronic information, optoelectronics, nanomaterials, phase change materials, superconducting materials; biological functional materials; energy and ecological environment materials; high-performance ceramics and new engineering plastics; powder, nano, microporous materials and high purity Metals and high-purity materials; surface technology and coatings and film materials; composite materials; smart materials; new structural functional additive materials, new structural materials with excellent performance, etc.   ◆Material instruments and equipment: particle size analyzers, thermal analysis instruments, chromatography, spectroscopy, mass spectrometry, X-ray instruments, elemental analyzers, surface and interface physical property testing, thickness gauges, material mechanical properties testing equipment, non-destructive testing instruments, other instruments and equipment, etc.   

Read More